THE INSTRUCTION ON APPLICATION
Compositions lubricant
"Suprotec-lux"
100 ml (further C.L.)
Scope
The engine of internal combustion with working volume from 1,6 up to 2,4 л (automobiles of release after 2000 г) manufactures: the USA, Japan, South Korea, the countries of Europe.
 
The order of application.
1stage:
Entering of 100 ml С.L. in working oil; Run of 500-1000 km.
2 stage:
Plums of oil;Washing of the engine by clean oil;
Replacement of the oil filter;Entering of 100 ml С.L. in new oil;
Run before regular replacement of oil.
3 stage:
Plums of oil;
Washing of the engine by clean oil;
Replacement of the oil filter;
Entering of 100 ml С.L. in new oil.
The note:
1. Before refuelling C.L. "Suprotec" it is necessary to mix carefully C.L. before full stirring a deposit (insignificant loss of a deposit is supposed).
2. Entering C.L. "Suprotec" is made in the hot engine.
3. With run less than 100 thousand in km is enough 2 stages of processing for automobiles.
4. After refuelling C.L. "Suprotec" the engine should be in working order not less than 10 minutes in any mode.
5. It is not recommended to apply at mechanical damages of details and units.
6. C.L. "Suprotec" it is compatible with any type of motor oils and does not change their properties.
7. Application of C.L. after the above-stated methods of processing more is not required.
8. For engines with working volume up to 1,6 liters and more than 2,4 liters requirement in C.L. will be determined at the rate of 50 ml on 1 liter working volume of the engine.
THE INSTRUCTION ON APPLICATION
Compositions lubricant
« Suprotec - GRANDEE АVТО »
500 ml (further C.L.)
Scope
The engine of internal combustion with working volume from 4,0 л
. 
The order of application.
1 stage:
Entering C.L. into working oil at the rate of 50 ml on 1 л. Working volume;
Run of 1000 km.
2 stage:
Replacement of oil;Replacement of the oil filter;
Entering C.L. into working oil at the rateof 50 ml on 1 л working volume;
Run before regular replacement of oil.
3 stage:
Replacement of oil;Replacement of the oil filter;
Entering C.L. into working oil at the rate of 50 ml on 1 л working volume.
The note:
1. Before refuelling C.L. "Suprotec" it is necessary to
mix carefully C.L. before full stirring a deposit
(insignificant loss of a deposit is supposed).
2. Entering C.L. "Suprotec" is made in the hot engine.
3. With run less than 100 thousand in km is enough 2 stages of processing for automobiles.
4. After refuelling C.L. "Suprotec" the engine should be in working order not less than 10 minutes in any mode.
5. It is not recommended to apply at mechanical damages of details and units.
6. C.L. "Suprotec" it is compatible with any type of motor oils and does not change their properties.
7. Application C.L. after the above-stated methods of processing more is not required.
8. For engines with working volume from above 4 Liters need in C.L. will be defined at the rate of 50 ml on 1 liter working volume of the engine.
THE INSTRUCTION ON APPLICATION
Compositions lubricant
« Suprotec - MKПП »
100 ml (further C.L.)
Scope
Processing of a mechanical box of switching of transfers, distributing box of transfers and reducers.
The order of application.
1 stage:
Entering C.L. into working oil at the rate of 20-30 ml on 1 litre of greasing.
Run of 5000 km.
2 stage:
Entering C.L. into working oil at the rate of 20-30 ml on 1 litre of greasing.
The note:
1. Before refuelling C.L. "Suprotec" it is necessary to
mix carefully C.L. before full stirring a deposit
(insignificant loss of a deposit is supposed).
2. Entering C.L. "Suprotec" is made in hot oil.
3. After refuelling C.L. it is necessary to maintain intensively
the automobile in a mode of switching of transfers not less than
100-200 m on each transfer.
4. It is not recommended to apply at mechanical damages of details and units.
5. C.L "Suprotec" it is compatible with any type of motor oils and does not change their properties.
6. Application C.L. after the above-stated methods of processing more is not required.
7. Processing transmission is made without replacement of oil, therefore it is recommended to make its replacement prior to the beginning of processing or to apply C.L. with insignificant run after replacement.
THE INSTRUCTION ON APPLICATION
Compositions lubricant
« SUPROTEC - АКПП »
80 ml (further C.L.)
Scope
Automatic box of switching of transfers of the car.
The order of application.
1 stage:
Entering of 30 ml C.L. in a working liquid.Run of 5000 km.
2 stage:
Entering of 30 ml C.L. in a working liquid.
Run of 50000 km.
3 stage:
Entering of 20 ml C.L. in a working liquid.
The note:
1. Before refuelling C.L. "SUPROTEC" it is necessary
to mix carefully C.L. before full stirring a deposit, insignificant
loss of a deposit is supposed.
2. After refuelling C.L. "SUPROTEC" the automobile should be in a mode of operation with run not less than 10 km.
3. It is not recommended to apply at mechanical
damages of details and units.
4. C.L. "SUPROTEC" it is compatible with a working liquid on a basis "Dextron" and does not change its properties.
5. Application of lubricant compositions after the above-stated methods of processing more is not required.
THE INSTRUCTION ON APPLICATION
Compositions lubricant
« SUPROTEC - ТНВД »
100 ml (further C.L)
Scope
The fuel pump of a high pressure of diesel engines of internal combustion.
 
The order of application.
1. Processing the car.
1 stage:
Entering of 50 ml C.L. in 50 litres of fuel. Run up to the full charge of fuel.
2 stage:
Entering of 50 ml C.L. in 50 litres of fuel.
2. Processing a lorry with working volume over 6 litres.
1 stage:
Entering C.L. is made at 50 % of capacity of a fuel tank at the rate of 1 ml C.L. on 1 litre of fuel. Run up to the full charge of fuel.
2 stage:
Entering C.L. is made at 50 % of capacity of a fuel tank at the rate of 1 ml C.L. on 1 litre of fuel.
The note:
1. Before refuelling C.L. "SUPROTEC" it is necessary to mix carefully C.L. before full stirring a deposit (insignificant loss of a deposit is supposed).
2. Processing is made in one stage by means of refuelling in a full fuel tank of necessary quantity C.L..
3. After refuelling C.L. "SUPROTEC" the engine should be in working order not less than 10 minutes in any mode.
4. It is not recommended to apply at mechanical damages of details and units.
5. C.L. "SUPROTEC" it is compatible with any type of fuel and does not change its properties.
6. Application of lubricant compositions after the above-stated methods of processing more is not required.
THE INSTRUCTION ON APPLICATION
Compositions lubricant
« SUPROTEC - ГУР »
60 ml (further C.L.)
Scope
The hydraulic booster of a rudder of the automobile.
The order of application.
1. The hydraulic booster of a rudder of the car.
1 stage:
Entering of 20 ml C.L. in a working liquid. Run of 5000 km.
2 stage:
Entering of 20 ml C.L. in a working liquid. Run of 50000 km.
3 stage:
Regular replacement of a working liquid.
Entering of 20 ml C.L. in a working liquid.
2. The hydraulic booster of a rudder of a lorry.
1 stage:
Entering C.L. into a working liquid at the rate of 20 ml on 1 litre of a working liquid. Run of 5000 km.
2 stage:
Entering C.L. into a working liquid at the rate of 20 ml on 1 litre of a working liquid.
The note:
1. Before refuelling C.L. "SUPROTEC" it is necessary to mix carefully C.L. before full stirring a deposit (insignificant loss of a deposit is supposed).
2. After refuelling C.L. "SUPROTEC" it is necessary to hang out forward wheels of the automobile and during 5 minutes. To rotate a steering wheel in the different sides.
3. It is not recommended to apply at mechanical damages of details and units.
4. C.L. "SUPROTEC" it is compatible with a working liquid on a basis "DEXTRON", and does not change its properties.
5. Application of lubricant compositions after the above-stated methods of processing more is not required. "Suprotec" "Description" "Catalogue" "Prices" "Power of attorney" "Certificates" "Contacts"
|
